Plumbing Basics: A Prerequisite for When Installing a Bathtub
Plumbing Basics: A Prerequisite for When Installing a Bathtub
Blog Article
Nearly everybody has got their personal views with regards to How to Install a Bathtub.
Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is readily obtainable, the job can move rapidly; if you need to open up a wall surface to eliminate the old tub and position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will need an assistant to leave the old tub as well as embeded in the brand-new one. Make sure you have actually certified on your own for the job and also are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This article will certainly assist you mount a brand-new tub in your washroom if you have currently purchased a new tub as well as don't need to transform the arrangement of your previous water supply pipes.
Your tools and also material checklist ought to comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any water staying in the system. The process of removing the existing taps can be fairly troublesome due to the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have actually been removed, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washers are in area in between the faucet and also the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for placement. The wooden boards are helpful in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bath tub till the level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
Turn on the water and check all joints and new pipework for leaks and tighten them if required. Load the tub as well as additionally inspect the overflow outlet and also the normal outlet for leaks.
Lastly, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has actually been used a minimum of when as this will resolve it into its final setting.
Preparing for the Installation
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps system to avoid stress on the bathtub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about complications with dampness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to enable the movement experienced when the bathtub is in use. The sealant can fracture rather very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily offered on the market. It is recommended to fit the tiles utilizing waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article about Installing A Bathtub through a friend on another web property. Liked our blog entry? Please share it. Let others locate it. Bless you for your time. Don't forget to pay a visit to our site back soon.
End your worries, dial! Report this page